Contract Finishing

Over the past 10 years, Rodeco has used its creativity and finishing knowledge for over 250 metal working customers with thousands of different parts.

The values we offer for our customers are:

  • Improved finish quality to improve our customer service to his customer
  • Consistent quality to mitigate the risk of mixed parts or inconsistent finish
  • Reduced wastewater
  • Lower labor cost for customer
  • Handled production spikes so customers meet their delivery schedules and sales
  • Reduced capital costs

Rodeco's Job Shop has helped some of our customers with descaling, rust removal, cleaning, brightening, and deburring of their parts.

The parts can be made of aluminum, brass, steel, stainless steel, plastic, copper, cast iron, silver (as in silver ware), gold and silver jewelry, ceramic tiles, and porcelain.

SAMPLES OF JOB SHOP CAPABILITIES

(click images to see enlarged view)

Part - Before

Deburring process

Problem

This cut wire part has a burr and sharp edge that would cut through its final coating. Our customer was needing over one million parts per week and couldn't keep up with demand.

Part - After

Deburring

Solution

Rodeco developed a process to clean and give the part a smooth radius on each end thus removing the burr and sharp edge. Rodeco processing over a million parts for them each week, resulted in less down time on their automatic assembly machines as well as freeing up their champler machines for their larger parts.

Parts - Before

Deburring processing

Problem

Brass parts had burrs and a dull look. The parts needed to be free of the burrs and a clean bright finish to them.

Parts - After

After Deburring

Solution

Rodeco developed a process to deburr and give the part a bright finish that well satisfied the customer.

 

Parts - Before

Deburring processing

Problem

The part is 3003 H14 1/8" thick aluminum that's been saw cut. It has a dull look and heavy burrs. The customer needed the burrs removed and a bright finish on this part.

Parts - After

After Deburring

Solution

Rodeco developed a process that removed the burrs and gave the part a bright finish.

 

Parts - Before

Deburring processing

Problem

The part is 3003 H14 1/8" thick aluminum that's been saw cut. It has a dull look and heavy burrs. The customer needed the burrs removed and a bright finish on this part.

Parts - After

After Deburring

Solution

Rodeco developed a process that removed the burrs and gave the part a bright finish.

 

Parts - Before

Deburring processing

Problem

Cast part (carburetor) with light burrs and very dull in appearance.

Parts - After

After Deburring

Solution

Rodeco developed a process to remove all burrs and give this part a very clean and shinny appearance. Customer very satisfied.

 

Problem

This part has to be cleaned to meet the customer's cleaning specs. The part is oily and holds oil and water in the "cup".

Parts - After

After Deburring

Solution

Rodeco's large capacity washer was programmed with a process cycle to completely clean and dry the parts to the customer's specs.

 

Problem

This part has burrs, is oily, and the RA's are too smooth for the gasket to stick.

Parts - After

Deburring & Rotary washing

Solution

Rodeco developed a 2 step process to solve the customer's problem by removing the burrs and giving them a minimum of 16 RA reading, then washing the parts in our Rotary washer to clean them completely.

 

Problem

Part is very oily after stamping and oil gets trapped in the crevices.

Parts - After

Deburring & Rotary washing

Solution

Our washer was programmed to perform the task of getting the part very clean and dry. Customer's air bag part is now very clean and meets their cleaning specs.

 

Problem

This part is very oily and cups water. The part has to be very clean and dry for the air bag installation.

Parts - After

Deburring & Rotary washing

Solution

Rodeco's washer was programmed to clean and dry this part. We can process over 100,000 pieces per day.